KB Category Archives: Petrochemicals

Heater Life Prediction

As an electric heating element ages, its resistance also changes. Many high Heater Life Predictiontechnology and extreme temperature applications employ exotic and expensive elements. Where the value of the products or materials being heated is high, the failure of a heater or heating element has a financial impact resulting from either reduced quality or scrapped materials. By measuring the current drawn by the element using an NK Technologies’ Current Transducer the resistance of the element can be determined and compared against a known ageing characteristic. When the element reaches a predetermined state it can be replaced prior to failure i.e. predictive maintenance. NK Technologies’ Current Transducers are used in conjunction with intelligent PLC systems when high power SCRs (also known as thyristors) or triacs are installed.

Continue Reading

Moisture Ingress on a Submersible Pump Motor

An NK Technologies’ Ground Fault Sensor installed on a submersible pump motor provides Submersible-Pump-Motoran easy to install replacement or addition to moisture sensors housed in the motor casing. Unlike moisture sensors that have to be wired back to the motor control center, the GF sensor is installed in the motor control center. By detecting the ground fault current resulting from moisture ingress or other potentially dangerous condition remedial action can be taken prior to catastrophic failure. Either the pump can be replaced at the next convenient time or switched off and a back-up pump started.

Continue Reading

Pump Load Monitoring

NK Technologies’ Current Transducers are used to monitor motor current and Pump Load Monitoringtherefore motor load. The output from the transducer may be fed to an analog or digital indicator or a Programmable Logic Controller (PLC) for more sophisticated monitoring and control.

NK Technologies’ Power Transducers provide load monitoring in more critical applications where the addition of voltage measurement and the determination of the phase relationship between current and voltage (power factor) provides more control.

NK Technologies’ Ground Fault Sensors keep the pumps safe by measuring ground leakage currents as low as 5mA. This also provides an alternative to moisture sensors used with submersible pump motors.

Also see these other articles:
Pump Jam & Suction Loss
Moisture Ingress on a Submersible Pump Motor

Continue Reading

Pump Jam & Suction Loss Protection

Pumps can become jammed due to foreign matter and cause damage to both the Pump Jam & Suction Loss Protectionpump and the motor before thermal overloads are tripped. Additionally a blockage in the suction line of the pump can cause the pump to run dry, overheat and break a seal.

By simply installing an NK Technologies’ self-powered Current Operated Switch in one leg of the motor overload (pump jam), underload (suction loss) or underload & overload can be detected quickly before damage occurs.

Continue Reading

Status Alarming

The auxiliary contacts in a motor starter are commonly used to indicate when the Status-Alarmingmotor is running. However, auxiliary contacts only indicate the position of the contactor, not the actual load status. If a downstream disconnect is open (for example, for maintenance) or the contact fails (either sticks or dirt build-up) there can be serious consequences.

At a large fish farm, failed aerator pumps resulted in massive stock losses. Because the auxiliary contacts remained closed when the pump failed, the alarm was never activated, the back-up pumps were not switched on and the fish suffocated due to lack of oxygen. Now NK Technologies’ Current Operated Switches have been installed to provide an alarm signal and a signal to automatically switch over to the back-up aerator pumps.

Continue Reading

Closed Loop Control

Normal linear AC induction motors have a current characteristic that increases with Closed Loop Controlload. Thus a measurement of current is proportional to the motor load. NK Technologies’ True RMS Current Transducers are designed to work in conjunction with variable frequency drives (VFD) and measure the current in the leg of the motor.

At an engine block manufacturing facility NK Technologies’ Current Transducers provide the input to a PLC used to position the rotating wire brushes in order to clean away burrs and debris after machining. As the current, and thus the load, changes so the brushes are positioned for optimal clean-up. Similarly Power Transducers are used to control the position of wheel wash brushes in a carwash. Power measurement provides a more linear relationship for motors and other loads with non-linear current characteristics. Current Operated Switches are used to co-ordinate operations between conveyor, washing and drying systems.

Continue Reading

DC Motor Installations

Many applications requiring high torque at low speeds, like bridge cranes and log DC Motor Installationscarriages, use DC shunt wound motors. Since it is relatively easy to control the speed of a DC motor by adjusting the voltage to the field windings, precise regulation is afforded to applications like printing press paper feeds or web control of multiple motors in the paper making process. Using an NK Technologies’ DC Current Transducer will provide an analog signal that can be used to keep the motor from over-current situations. Using an NK Technologies’ DC Current Operated Switch will insure that if the motor field supply is lost, the motor will not over-speed to the point of self-destruction.

Continue Reading
Registration Required
Need an Account? Sign Up
x