Provides simple solution for monitoring current in applications where one-piece sensors are impractical or impossible to install
NK Technologies introduces CTC Series Signal Converters. With the CTC series users can utilize an existing standard 5 amp secondary CT or low voltage (0.333 VAC) ProteCTTM current transformer with non-contact ranges as low as 0-5 amps over a conductor to produce a standard 4-20mA two-wire, loop-powered signal. With DIN rail mounting and a 24 VDC loop-powered supply, the CTC series provides simple snap-in installation that requires no calibration because the primary current transformer ratio provides the scaling required without any installer intervention.
Large aperture design makes it easy to seamlessly monitor any circuit up to 1200 amps
NK Technologies introduces DT Series Large Aperture Current Transducers. The DT series combines a hall effect sensor and signal conditioner into a single package for use in DC current applications up to 1200 amps. Factory calibrated ranges simplify operation and eliminate zero and span pots. Industry standard 4-20mA, 0-5VDC or 0-10VDC outputs are magnetically isolated from the input to provide maximum safety, and eliminate insertion losses. Internal power regulation delivers reliable operation and helps keep installation costs low, even in applications with unregulated power. A DIN-rail mount enclosure makes installation easy..
Ring design easily slips onto a conductor to give a solid-state contact for cost effective and reliable current flow indication as low as 0.5 amps
NK Technologies introduces the AS1 Series Compact Case Current Sensing Switch. With its tiny 1 inch housing, the AS1 is a compact and cost-effective solution that enables users to monitor an energized circuit in tight spaces. The easy-to-use ring design easily slips onto a conductor to reliably detect currents as low as 0.5A with a single conductor pass, eliminating the need to wrap conductors multiple times. Reliable, solid-state output with no moving parts provides a nearly unlimited number of operations..
Innovative design enables installer to pass the coil around the conductors, without having to disconnect existing wires. NK Technologies introduces ATCR Series Current Transducers. ATCR flexible loop current transducers are a perfectly matched and factory calibrated sensing coil and True RMS signal conditioner that use just two wires to provide the power supply and output signal, while eliminating the need to disconnect existing wires. This makes them a uniquely simple and convenient means of monitoring resistive or inductive loads to detect current usage on large machines using AC current up to 2000 amps. They meet UL508 and CE requirements, making them suitable for global application.
VTD series is a cost-effective solution for monitoring, detecting and diagnosing voltage conditions in DC powered installations NK Technologies introduces VTD Series high-performance voltage transducers. Packaged in a compact and easy-to-install 35mm wide DIN-rail enclosure, the VTD series senses voltage in a wide variety of DC powered installations, including industrial motors, battery chargers, photovoltaic arrays and wind generators. These cost-effective voltage transducers help avoid motor overheating by detecting below normal voltage conditions, and detect voltage conditions that can stress or damage starter components. Monitoring DC voltage enables operators to know that the system is ready even before there is a load connected to it.
Innovative design enables installer to pass the coil around the conductors, without having to disconnect existing wires NK Technologies introduces ATCR Series Current Transducers. ATCR flexible loop current transducers are a perfectly matched and factory calibrated sensing coil and True RMS signal conditioner that use just two wires to provide the power supply and output signal, while eliminating the need to disconnect existing wires. This makes them a uniquely simple and convenient means of monitoring resistive or inductive loads to detect current usage on large machines using AC current up to 2000 amps. They meet UL508 and CE requirements, making them suitable for global application.
CTC Series Signal Converters allow you to use an existing standard 5A secondary or low-voltage ProteCT™ current transformer over a conductor to produce an industry standard 4-20mA two-wire, loop-powered signal. The signal is proportional to the current in the primary circuit. The CTC series snaps onto a standard DIN rail. The output is connected to the load and a 24 VDC source and the current transformer is connected.
ATQ Series AC Current Transducers have a patented frequency output design used as an input to high-speed counter or frequency PLC modules, panel meters or programmable relays. Use where no analog inputs are available. Eight ranges, from 0–2 to 0–200 A, across three models provide the best available resolution. The ATQ Series AC Current Transducers are designed with a split-core case for easy installation.
NK Technologies’ flexible cable current sensors wrap around the conductor using very little space. The cable is connected to a signal conditioner located up to several feet away from the conductor, and produces an industry standard 4 to 20 mA signal in proportion to the AC current. With ranges of 0–500 to 0–2000 amps and frequencies to 400 hertz, the ATCR series is well suited for a wide range of applications.